- Lsi megaraid storage manager linux update#
- Lsi megaraid storage manager linux Pc#
- Lsi megaraid storage manager linux windows#
I would also then, need to figure out a way to find which physical disk belongs to each logical disk, so I can properly make a map of the server. Now, I'll be honest and admit that I'm very new to working with RAIDs and servers, I've done a lot of research and I'm assuming that one of the drives isn't working properly and needs to be replaced, but I can't seem to be able to pinpoint which one it is, I've ran several commands but I'm not really sure what sort of info I'm looking for, so I'd really appreciate any advice you guys can offer to a complete newbie. All drives are online and working, none is set as foreign and yet, the status of the virtual drive is set to partially degraded and sometimes as degraded. The issue I'm having is, whenever the server is restarted, the alarm starts beeping but there doesn't seem to be any obvious reason to this. However, shutdown seems to leave the disk in an unclean state and I have to run fsck on reboot.I recently inherited a SuperMicro server running a hardware RAID 6 with a MegaRAID SAS 8708ELP on Linux and it's a big mess, according to my boss all the drives are scrambled and physical locations aren't the same as logical ones on the virtual drive. megaraid_sas 0000:04:00.0: jbod sync map : uname -r megaraid_sas 0000:04:00.0: firmware crash dump : no megaraid_sas 0000:04:00.0: unevenspan support : no megaraid_sas 0000:04:00.0: Jbod map is not supported megasas_setup_jbod_map 4941 megaraid_sas 0000:04:00.0: INIT adapter done megaraid_sas 0000:04:00.0: Secure JBOD support : No megaraid_sas 0000:04:00.0: Online Controller Reset(OCR) : Enabled megaraid_sas 0000:04:00.0: FW now in Ready state
Lsi megaraid storage manager linux Pc#
I have a PC with the same (or similar) RAID controller (with only one disk attached), but it seems to work for me: lspci | grep -i raidĠ4:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2008 (rev dmesg | grep mega
![lsi megaraid storage manager linux lsi megaraid storage manager linux](https://sc02.alicdn.com/kf/HTB19k.JBOCYBuNkHFCc763HtVXan/232844690/HTB19k.JBOCYBuNkHFCc763HtVXan.png)
Upgrading the controller's firmware did not change anything. I'll try as soon as I updated my backups.
Lsi megaraid storage manager linux update#
Hence, I now suspect that a firmware update may solve my problem. I checked the firmware version and it is quite outdated. This has never occurred before and only happens after booting Linux.
Lsi megaraid storage manager linux windows#
Additionally, after rebooting Windows after booting a Linux LiveCD, the MegaRAID Storage Manager pops up to complain about a firmware error.
![lsi megaraid storage manager linux lsi megaraid storage manager linux](http://here.vixual.net/blog/images/2013/10/vmware/msm-dashboard.png)
This controller should work fine with Linux according to here. megaraid_sas 0000:03:00.0: Failed to init firmware megaraid_sas 0000:03:00.0: FW now in Ready state Here are some details of what I'm experiencing: # lspci | grep MegaĠ3:00.0 RAID bus controller : LSI Logic / Symbios Logic MegaRAID SAS 2008 (rev 03) Has anybody gotten this card to work, or a related model? Ubuntu 16.04 is having trouble working with a LSI MegaRAID SAS 9240-4i hardware RAID controller.